Step 9: Moose Racing Radiator Braces

You’ll find aluminum radiators on all high performance dirt bikes built today. Due to weight and size issues related with dirt bikes these aluminum radiators are placed in tight areas and at the front part of the bike where they will get hammered with rocks, sticks, and crashes. If your radiators get damaged to the point of it leaking coolant then you race or trail ride has ended. Take care of your cooling system by performing proper maintenance and invest in radiator braces for the radiator protection.

Once you have drained all the coolant remove the water pump cover and check for debris or even corrosion. Grab the water impeller and see if there’s any movement up and down. Any movement would indicate the water pump shaft bearings are worn. In most cases if the bearings are worn then the seals are worn and leaking water in to the crank case. The best repair is to replace the water pump shaft (usually grooved from seals), bearings, and seals as a set because the parts are not very expensive and can be purchased from Motosport.com as they warehouse a huge selection of O.E.M dirt bike parts for all major brands.

Some bikes have a bleed bolt on top of the cylinder head that is used to purge air out of the engines cooling passages and some are self bleeding by design. If the air is not bleed completely from the system it can prevent the coolant from circulating and the engine temperature will rise until the radiator caps releases and coolant is spilled out on the ground (boil over). Remove the radiator cap, fill the system to the top of the radiator, loosen the bleed bolt on top of the cylinder head until a solid steady stream of coolant is flowing out and then tighten bleed bolt. The other radiator on the bike is going to be self purging of air, it is being filled from the bottom and pushes all the air to the top where there’s a connection hose between both radiators. Next top off the radiator and install the cap, run the engine for 5-10 minutes and then check the coolant level again. Caution: Make sure you let the engine cool down before removing the radiator cap, hot coolant can burn your hand.

Radiators are very expensive to replace so protect them. For this project I choose Moose Radiator Guards. These braces help keep the radiators from bending or being crushed due to a crash. You can also remove the factory plastic louvers and replace them with an aftermarket aluminum screen which help protect the radiator core from rocks, sticks etc. Remember that the factory louvers help channel air flow in to the radiators core for proper cooling, so removing them can cause some overheating issue in certain riding condition.

Moose Radiator Guards Details

  • Two pieces design.
  • Comes with all needed hardware.
  • Installation instruction included.
  • I would recommend using Loctite on all assembly fasteners.
  • Very strong and ridged system.
  • Radiators still can float or move within the guard as needed as they are still mounted with the original grommets.
  • Bent or twisted radiators? Better get them straighten before installation.
  • Frame mounted, Excellent side protection.
  • Great fit and function overall.

You can improve the efficiency of the cooling system by switching radiator cap marked with 1.6 which will raise the pop off pressure and increase boiling point. You will find some aftermarket companies that offer improved water impellers and housing, and even larger radiators to help improve cooling efficiency. There are special coolants like Maxima Cool Aide that can be used to help improve cooling efficiency.

moose racing


Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77

Warning: Division by zero in /home3/hughes12/public_html/wp-content/plugins/flagallery-skins/phantom/init.php on line 77